Please put in the order notes which orientation you would like the fittings (Horizontal or Vertical) if you are not sure feel free to call us on 0333 1234 365 and we should be able to help. Also when selecting booster pump head size please contact us if you need advice. Large Booster Pump with fittings (Horizontal Or Vertical Fittings)

The industry leading 12V DC water pump - 100psi, 5.2lpm open flow rate. Very reliable - suitable for operating one pole of any height with upto 100m of hose.

Includes 1 Shurflo strainer with male / female 1/2" BSP inlet and outlet, 2 1/2" barbed hose tail fittings and 2 stainless steel hose clamps. Suitable for our standard Shurflo pump with 1/2" male BSP ports. Image for illustration only - pump not included.

100PSI SHURFLO PUMP & FLOWMASTER DIGITAL FLOW CONTROLLER ON PANEL READY TO CONNECT TO YOUR BATTERY AND PIPES.

 

Purefreedom Aquatec pump 100 PSI 5.5LPM

Straight Fitting Kit for Aquatec Pump

Elbow Fitting Kit for Aquatec Pump

12V DC 60psi diaphragm water pump. Similar performance to our 100psi Shurlfo Pump but with a 5.3lpm open flow rate and better self priming capabilities. Suitable for any length of water fed pole and upto 100m of hose. Comes with 3/8" female threaded ports.

12V DC 100psi diaphragm water pump. Similar performance to our 100psi Shurlfo Pump but with a 7.6lpm open flow rate and better self priming capabilities. Suitable for any length of water fed pole and upto 100m of hose. Comes with 3/8" female threaded ports.

A high quality Aquatec 24v AC pump for boosting water pressure into your reverse osmosis system thereby increasing output, efficiency and even water purity. Suitable for our 200, 300 and 450 GPD Reverse Osmosis units. Simply install the pump inline between your prefilters and RO membranes. Pump only.

240v - 24v Transformer for our Aquatec Reverse Osmosis Booster Pump

A high quality Aquatec 24v AC pump for boosting water pressure into your reverse osmosis system thereby increasing output, efficiency and even water purity. Suitable for our 200, 300 and 450 GPD Reverse Osmosis units. Simply install the pump inline between your prefilters and RO membranes. Water temperature, TDS (purity) and mains pressure will all affect final RO output and quality, however we have tested this pump at our workshops on one of our 300 GPD Reverse Osmosis units with an inlet water temperature of 16C a TDS of 290ppm and a pressure of 50psi. RO output rate more than doubled with the pump installed and the output TDS dropped from 018ppm to 010ppm offering considerable savings on DI resin usage over time. Based on this setup in these conditions the booster pump would reduce the time taken to produce 250 litres of pure water from 14 hours 30 mins to just 6 hours and 15mins. Installation instructions included. Supplied with a transformer for 240V mains power.

Please put in the order notes which orientation you would like the fittings (Horizontal or Vertical) if you are not sure feel free to call us on 0333 1234 365 and we should be able to help. Also when selecting booster pump head size please contact us if you need advice. Large Booster Pump with fittings (Horizontal Or Vertical Fittings) (The last 2 photos show the pump with the Direct Online Starter)

Rotary Vane 800 LPH Booster Pump Rotary vane pump head as used on our Hi volume and van mounted Reverse Osmosis systems

Spare Motor For Our 'Large Booster pump' Heavy duty 230 volt single phase AC motor for use with a flexible coupling to drive the RO vane pump, flexible coupling, vane pump and control gear available separately.    

Coupling for large booster pump

Booster pump control for 4 inch membranes

DOL starter for 230 volt booster pump motor, provides motor overload protection, prevents switching back on after supply has been interrupted. Comprises of an enclosure, manual motor starter, low voltage device and 2 20mm cable glands.

For the rapid movement of large amounts of water a high volume pump such as this is a must. At a 110 litre per minute rating this transfer pump will have most water fed pole systems filled in a matter of minutes. Simply drop into your storage tank, plug in and go!

Complete kit including our mains powered 100 litre per minute submersible transfer pump, 5 metres of 1" high quality braided PVC transfer hose, filling nozzle and stainless steel hose clamps.

The pressure switch is desgined to save the pump from damage by switching it off when the line pressure reaches a certain value. A faulty pressure switch can cause permanent damage if not replaced.

A damaged or worn valve assembly will prevent a pump from pumping effectively, however it is a very simple procedure to replace.